Nick Carver Photography Blog

Photography Tips, Tutorials, & Videos


DIY: Tripod Snow/Sand Shoes

DIY Tripod Snow Shoes

I shoot at the beach quite often, so my tripod sees a lot of sand. The sand and salt water ain't no big deal because I always clean my tripod after a trip to the coast, but one thing that drives me nuts is when my tripod sinks in the sand as the tide washes in and out around it. Whenever the waves swirl around those legs, the thing just starts sinking like Indiana Jones in quicksand. And since I use long shutter speeds quite often when shooting seascapes, this phenomenon has forced me to stick to rocky areas or timing my shots to finish before the water reaches me.

So I had the brilliant idea (after years of putting up with this problem) to steal the brilliant idea of other photographers and utilize some "snow shoes" to prevent the sinkage. I haven't had a chance to try them out yet, but the concept is solid - give the tripod legs a wider foot, and hopefully the water will be able to swirl around them all sunset long without the quicksand effect. To be honest, I'm skeptical and my hopes aren't high, but we'll see.

Being the DIY kind of guy I am, I thought I'd make my own. With $30 or so worth of materials, you can make your own, too. But if you're smart, you'll just buy these ready-made ones by Manfrotto. And wouldn't you know it, they're about $30. My home made ones may not be cheaper, but at least they're uglier., man. But mine do secure higher up on the legs, so maybe they're more secure. But probably not...

Anyway, here's what you'll need

  • 3x adjustable flag pole brackets - like these
  • 1x package of furniture sliders - like these
  • 1x washing machine & dishwasher hose 1.75"x7/8"x2' (not like what you think, see the pictures below)
  • 12x machine screws 3/4" long with nuts
  • Sharpie
  • Awl

Step 1: Remove the foam padding from the furniture sliders

DIY Tripod Snow Shoes

DIY Tripod Snow Shoes

Step 2: Set the flag pole bracket on the upside-down furniture slider and mark the screw hole openings with a Sharpie

DIY Tripod Snow Shoes

DIY Tripod Snow Shoes

Step 3: Poke holes through each Sharpie marking with an awl

DIY Tripod Snow Shoes

Step 4: Attach the flag pole bracket to the furniture slider with screws and nuts

Step 5: Cut a piece of the rubber hose to slide into the flag pole bracket - make it just long enough to stick out about 1/2"

This little length of rubber hose protects your tripod legs, fills the gap in the flag bracket for a tight fit, and gives something for the tightening screw to brace against. Make sure the rubber hose can fit over your tripod legs before buying it. If your tripod legs are thicker than mine, you may not need it at all.

DIY Tripod Snow Shoes

DIY Tripod Snow Shoes

DIY Tripod Snow Shoes

Step 6: Repeat 2 more times

DIY Tripod Snow Shoes

So there you go. Now you have 3 adjustable tripod all-terrain shoes. Use the screw on the side of the flag pole bracket to tighten the shoe to the tripod. And don't worry about scuffing up your tripod because the rubber tube inside provides more than enough protection.

Enjoy your ugly, DIY, may-or-may-not-be-as-good-as-the-real-thing tripod shoes!

DIY: Tripod Leg Pads

I've had padding on my tripod legs for at least 7 years now and I am thoroughly hooked. They're great for protecting your hands against the biting cold of the aluminum or carbon fiber and they make throwing your tripod and camera over your shoulder a lot more comfortable.

Now, you could spend around $25 plus shipping for some pre-made tripod leg wraps that may or may not fit your tripod perfectly, but that's way more money than you need to spend and, honestly, it just ain't custom enough. You need to make your tripod YOURS. It's gotta be like an extension of your own body - a piece of equipment that you know better than the back of your own hand. Like an emperor penguin identifying its offspring in a sea of black and white, you should be able to know your tripod just from the squeak of its joints. That's why you need to MAKE your own tripod leg pads.

Okay, maybe that's a bit extreme. But making your own tripod leg wraps is much cheaper and you'll probably really enjoy doing it. This post breaks down how I do it with about $10 worth of materials and an easy half hour in front of my TV. Don't glaze over this post if you want to make your tripod leg wraps right, there are some very important details you won't want to screw up.

First off, get your materials. You'll need some foam pipe insulation (found at most hardware stores) long enough to cover all three legs and wide enough in diameter to nearly make it all the way around. You want the foam padding to be just a little bit narrower than the legs - too wide and they will rotate around too easily and drive you nuts. I purchased a single 6-foot piece of foam insulation made for pipes 3/4" wide for $2.99 at Ace Hardware.

Foam Pipe Insulation

You'll also need a couple rolls of athletic tape - the kind of tape they use to wrap grips for hockey sticks. This stuff can be found at almost every sporting goods store and runs a few bucks a roll. I went ahead and bought the 6-pack for a better price per roll (you'll want to replace these pads after they start to wear out anyway). You'll also need some scissors to cut the tape and a razor to cut the foam insulation. Other than that, you're good to go.

Your materials

First, cut the foam pipe insulation to the desired length. You'll want it to fit perfectly over the top leg section (from the joint to the first leg lock). You can do this by first marking your cut line. Hold a pen against the foam insulation and rotate the foam around (not your pen) so the pen line circles the entire foam cylinder - kind of like a wood worker using a lathe.

Mark your line

Then take your razor blade and insert it into the pen line. Rotate the foam insulation around again, causing the blade to make a full circle clean cut. This method works far better than scissors or trying to cut straight down through the foam. Then slide your razor down the seam going lengthwise on the foam so that it splits open into a "C" shape. Test the pads for fit and cut more if necessary.

Insert razor into mark line and rotate foam to cut

Then cut down the pre-scored seam

With the foam pads OFF the tripod, you're going to wrap athletic tape around the bare tripod legs in three places - towards the bottom near the leg lock, towards the top near the joint and another right in the middle. Only wrap it 1 strip wide and no need to overlap much. This tape isn't meant to protect the legs, it's simply put there to give the foam insulation (that will be on top of it) something to grip to so that it doesn't rotate around a lot. You should have 3 strips of athletic tape around each leg.

Wrap tape around bare tripod legs

Wrap in 3 spots for a good grip

Now, place the foam pipe insulators on the legs right over top of the athletic tape you just applied. Line up the seams towards the insides of the legs.

Line up seams towards inside

Now you're going to take your athletic tape and wrap around the foam insulation in the same 3 spots you applied tape to the bare legs. Only wrap 1-strip wide and make only 2 or 3 overlapping passes. Wrap it real tight. The idea here is these strips will apply tension to the foam pads right over the tape you put under it. This will create enough friction to keep the pads from rotating and will keep the pads in place for the next step.

Wrap strips of tape around foam...

Again, you should have 3 strips of tape going around the padding - towards the bottom near the leg lock, towards the top near the joint and another right in the middle. All three legs should have the padding on with 3 strips of tape around each.

...right over top of the strips underneath

Now it's time to seal off the padding by wrapping it entirely in athletic tape. This will create a good, soft grip around the foam, it will protect the foam from ripping, keep it from rotating and will give it one hell of a professional look.

To do this, you're going to take your roll of tape and just wrap the tape around the legs in somewhat of a spiral shape. It's just like if you were wrapping the grip for a tennis racquet, golf club or hockey stick. The important thing here is to START AT THE BOTTOM OF THE FOAM PADDING AND WORK YOUR WAY UP! This will cause the overlap to point downwards - just like shingles on a roof - which helps with water resistance and overall comfort. DO NOT START AT THE TOP - you will regret it when your tape starts peeling off the foam.

Start off by making 2 turns around the very base, then bend the tape to start wrapping around the legs at an angle so that it proceeds in a spiral. Overlap each pass by about 25% until you get to the top.

Bend tape to start upward spiral

Keep a tight, even pressure on tape as you make your way up.

Finish it off by straighting out the tape and making 2 turns around the very top. Cut the tape so the end of it stops towards the inside of the legs - not the side or outside. Keep the tape wrapping real tight around the foam the entire time! Repeat this process for the remaining legs and you're done!

There you have it! Now your tripod has some awesome new pads and you're wallet ain't too much worse for the wear!

The tape might fray a bit, but just rip the strings off as they come. These pads will last quite a bit longer than you'd think. I've had mine on for over 3 years and they're showing no signs of breaking down. When they finally do wear out or just get a little too dirty for your liking, switch 'em out for some new ones for only another $10.00!

Thanks for reading!

Homemade Plamp

One of the most frustrating things in macro photography is trying to keep flowers still while photographing them. At the high magnifications of close-up photography, even the slightest trembling in the wind will ruin a shot. That's why someone smarter than me invented the Plamp (plant clamp) - an articulating arm with clips on either end that attaches to your tripod and can hold a flower steady for you.

It's a really great product, but I just couldn't justify the price, size and weight for something I'll use so rarely. So, instead, I made a trip to my hardware store, picked up a yard or so of their heaviest-gauge wire, bought a pack of charging clips and decided to throw an imitation plamp together myself.

Total cost of materials: About $3.00.
Total assembly time: About 10 minutes

Basically you just attach a clip to either end of the wire and you're done. You can wrap it around your tripod and position the arm to hold the flower just right. Of course, this isn't as good as the Plamp itself (it isn't as sturdy and is a little "springy"), but it definitely is cheap. Here's a shot I took with and without my homemade plamp (both pictures: 1/25 at f/14):



See? Much better. Now go out and get your supplies!